The SILI CQX submersible pump is also called CQW or QW submersible pump sometimes. It is a kinf of submersible centrifugal sewage pump, with non-clogging impeller, and portable design. This centrifugal marine pump is mainly used for sewage bilge, fire fighting, deck-wash and emergency flood water for marine and off shore purpose.
CQX submersible pump is suitable for sewage, bilge and oily water, max liquid temp 60 C degree, maximum diameter of the solid grain 50% of that of the pump outlet flange Max liquid temp 60 C degree, Max S.G. 1200kg/m3. The maximum diameter of the solid grain going through the CQX submersible pump has not to be larger than 50% of that of the pump outlet flange. Refer to more details from right link onsides the pump catalogue, specification and manual. CQX pump spare parts can be also available in our sides.
CQX submersible pump Design Features:
a. Class F Insulation level, max working temp 155 C degree. The effective seal makes its IP 68 high protective level. An over heating device for the motor is optional.
b. With the optimized design, the big channel impeller (no-clogging type) will not be blocked up when to transport sewage/bilge with big impurity or long fiber.
c. A oil chamber is located between the motor and the pump. Oil can lubricate and cool the mechanical seal and prevent water from penetrating into the motor. A water-leakage probe(above 5kw) is mounted inside the oil chamber to check water leakage and it will give a warning signal, when the mechanical seal on the pump side leaks.
d. Double separate mechanical seal work individually to separate the motor from the pump seal, to provide the motor with a dual protection.
e. Quality bearing with a reasonable configuration, can extend the duration of the pump. At the top and the bottom of the motor, there is both a rolling bearing. While in the bottom of the motor, there is another thrust bearing. (double bearings at the bottom of the motor side).
f. A special cooling water jacket is optional if request.
g. Standard material for bronze for the pump casing, impeller and cover, stainless steel for pump shaft. An optional stainless steel material for pump casing, cover and impeller.
h. Portable design, with a standard 10m water-proof cable. The fire hose and quick connection port can be provided as request.
Refer to pump and spare parts details from the CQX submersible pump or CQW sewage pump catalogue. And contact us more information for CQX submersible pump specification, manual, installation dimension and so on.
Technical details:
–Motor: 2 or 4 pole quality IEC motor configurations, with high level class(class F or higher) and insulation(insulation IP68), in both 50Hz or 60Hz, Y-H series, suitable for marine purpose, Starting in direct type(small power).
–Material: pump and motor casing/pump body/pump wear ring: bronze(ZCuZn16Si4), shaft: stainless steel(stainless steel and cast iron material is optional)
–Shaft seal: Shaft seal upper, mechanical seal, single face type, SIC(silicon carbide)/hard alloy; Lower, mechanical seal, double face type, material: SIC(silicon carbide)/hard alloy and SIC(silicon carbide)/ceramics.
–Bearing: upper, one enclosed antifriction bearing, lubricated by grease, lower, one enclosed antifriction bearing, another thrust bearing, all lubricated by grease
–Leakage detection: a water leakage detector is located on the upper of the pump, a oil chamber is insides pump, oil can lubricate and cool the mechanical seal and prevent water from penetrating into the motor, a water-leakage probe (above 5kw, optional)is mounted inside the oil chamber
–Cooling jacket: a special cooling water jacket is optional if request
–Accessory: standard 5m water-proof electric cables, lifting hooks, and so on
Standard pump supply range: including pump, coupling, common base, motor and standard accessories.
Optional supply: accessories, outlet connect elbow, starter, longer water-proof cables and so on
Suggested min spare parts: 1 pcs of impeller, 1 pcs of shaft, 2 pcs of mechanical seal, 2 sets of bearing, 6 pcs of O-ring
Certificate of classification society available: CCS
Standard packing: plywooden case.
Production time: in about 20 to 35 days
Warranty time: one year after shipment.
Case reference: it is updated in case blog.
Please click the following link for relative case.
a. 2015.12-12 pcs of CQX marine submersible pump to a Thailand client.
Usage or application: This pump can be use for bilge, sewage, emergency flood and so on.
Please click the relative category in right of the production picture for more information.
Kindly send your specific inquiry, we will reply you in one working day.
Please contact us through:
a. directly send us an e-mail, sales@silipump.com(suggested).
b. contact us throught the online Skype or Online message(just working time in working day).
c. leave a message on the web.